Layer-by-Layer Dynamic Shear Modulus in the Cross-Section of a Particle Board. P.143-156

Complete text of the article:

Download article (pdf, 0.9MB )

UDС

674.8:674.049.2:542.973

DOI:

10.37482/0536-1036-2022-5-143-156

Abstract

The research results are aimed at the formation of ideas concerning the features of molecular motion of the components of the outer and inner layers of the particle board material in the temperature range from room temperature to 275–300 °C, as well as at revealing the fact of binder undercuring in the inner layers. The paper provides data on the temperature dependences of the dynamic shear modulus of the outer and inner layers of the particle board material, obtained by dynamic mechanical analysis using a torsion pendulum. We found significant differences in the nature of the dependencies for samples taken at different distances from the surface layers. The material of the outer layers is characterized by the typical pattern of a continuous irregularly consistent decrease in the dynamic shear modulus with increasing temperature, which is common to most polymeric and composite materials. A short-term intermittent increase in the dynamic shear modulus relative to neighboring areas was detected in the inner layers at 140±5 °C, which is not typical for materials in a stable state. There is also a tendency for the dynamic shear modulus of the particle board material to decrease at room temperature with distance from the outer layers, due to the heterogeneous fractional composition and differences in the nature of chemical cross-linking during hot pressing. It has been assumed that the detected anomalous increase in the dynamic shear modulus in the inner layers of the material at 140±5 °С is a symptom of the binder post-treatment process directly in conditions of its heating when measuring the dynamic shear modulus by dynamic mechanical analysis. Thus, it is concluded that the particle board sample shows maximum curing of the thermosetting binder in the layers, which are 4.5–5.0 mm distant from both surfaces. Partial undercuring of the binder occurs in the inner layers, which are more than 5.5 mm away from the surfaces. Thus, it is shown that the method of dynamic mechanical analysis can be used as a tool to control the presence in the inner layers of the particle board material of the components of thermosetting binder, undercured in the hot pressing process, which will help to obtain a material with more stable characteristics.

Authors

Yuri G. Skurydin¹*, Candidate of Engineering, Assoc. Prof.;ResearcherID: AAE-1212-2019, ORCID: https://orcid.org/0000-0002-1852-2152
Elena M. Skurydina², Candidate of Engineering, Assoc. Prof.;ResearcherID: AAB-4572-2021, ORCID: https://orcid.org/0000-0002-1707-8846

Affiliation

¹Altai State University, prosp. Lenina, 61, Barnaul, 656049, Russian Federation; skur@rambler.ru*
²Altai State Pedagogical University, ul. Molodezhnaya, 55, Barnaul, 656031, Russian Federation; skudem@rambler.ru

Keywords

particle board, dynamic mechanical analysis, dynamic shear modulus, wood, thermosetting resin, binder curing, composite material

For citation

Skurydin Yu.G., Skurydina E.M. Layer-by-Layer Dynamic Shear Modulus in the Cross-Section of a Particle Board. Lesnoy Zhurnal = Russian Forestry Journal, 2022, no. 5, pp. 143–156. (In Russ.). https://doi.org/10.37482/0536-1036-2022-5-143-156

References

1. Beusheva O.S., Skurydina E.M., Chemeris M.M., Musko N.P., Skurydin Yu.G. The Influence of Pressing Condition on Properties of Plate Materials Made of Hydrothermally Treated Larch Wood. News of higher educational institutions. Construction, 2006, no. 5(569),pp. 48–50.  .
2. Vasiliev V.V., Hosseini S.Z. Modern Requirements for Wood-Based Panels for Finishing. Wood-Based Panels: Theory and Practice. Proceedings of the XX International Scientific and Practical Conference. Ed. by A.A. Leonovich. Saint Petersburg, Polytechnic University Publ., 2017, pp. 62–71.  .
3. Volkova S.N., Sivak E.E., Pankrat’yeva O.V., Levanov G.V., Boyev N.V., Konotopchenko O.A. Quality Control of Building Materials from Forest Industry Waste. Regional’nyy vestnik, 2021, no. 3(59), pp. 33–36.  .
4. Wood-Based Panels: Theory and Practice. Proceedings of the XX International Scientific and Practical Conference. Ed. by A.A. Leonovich. Saint Petersburg, SPbSTU Publ., 2017. 122 p.  .
5. Erykhov B.P. Non-Destructive Methods of Examination of Pulp and Paper and Wood Based Materials. Moscow, Lesnaya promyshlennost’ Publ., 1987. 228 p.  .
6. Karkhova S.A. State Analysis for Production and Trade of Boards and Plywood in the World. Baikal Research Journal, 2018, vol. 9, no. 2, art. 6.  . https://doi.org/10.17150/2411-6262.2017.9(2).6
7. Otlev I.A. Intensification of Particle Board Production. Moscow, Lesnaya promyshlennost’ Publ., 1989. 192 p.  .
8. Skurydin Yu.G., Skurydina E.M. Method of Determination of the Noncompletion of the Process of the Thermoreactive Binder Curing of a Particle Board. Patent RF, no. RU 2 619 359 C1, 2017.  .
9. Perepechko I.I. Acoustic Research Methods for Studying Polymers. Moscow, Khimiya Publ., 1973. 295 p.  .
10. Safin R.G., Stepanov V.V., Khairullina E.R., Gainullina A.A., Stepanova T.O. Modern Construction Composite Materials Based on Wood Waste. Bulletin of the Technological University, 2014, vol. 17, no. 20, pp. 123–128.  .
11. Skurydin Yu.G. Structure and Properties of Composite Materials Obtained from Wood Wastes after Explosive Hydrolysis: Cand. Eng. Sci. Diss. Barnaul, 2000. 147 p.  .
12. Skuridina E.M. Development of the Technology of Composite Materials Based on Wood and Polymer Fillers: Cand. Eng. Sci. Diss. Barnaul, 2006. 170 p.  .
13. Startsev O.V., Salin B.N., Skurydin Yu.G. Barothermal Hydrolysis of Wood in Presence of Mineral Acids. Doklady Akademii Nauk, 2000, vol. 370, no. 5, pp. 638–641.  .
14.Chubinsky A.N., Varankina G.S., Rusakov D.S. Technology of Wood-Based Panels.Saint Petersburg, SPbFTU Publ., 2019. 37 p.  .
15.Shakhzadyan E.A., Kvachev Yu.P., Papkov V.S. Temperature Transitions in Wood and Its Components. Polymer Science. Series A, 1992, vol. 34, no. 9, pp. 3–14.  .
16. Fengel D., Wegener G. Wood: Chemistry, Ultrastructure, Reactions. Berlin, De Gruyter, 1983. 613 p. https://doi.org/10.1515/9783110839654
17. Müller U., Pretschuh C., Mitter R., Knappe S. Dielectric Analysis as a Cure Monitoring System for UF Particle Boards. International Journal of Adhesion and Adhesives, 2016, vol. 73, pp. 45–50. https://doi.org/10.1016/j.ijadhadh.2016.07.016
18. Oktay S., Kızılcan N., Bengu B. Oxidized Cornstarch – Urea Wood Adhesive for Interior Particleboard Production. International Journal of Adhesion and Adhesives, 2021, vol. 110, art. 102947. https://doi.org/10.1016/j.ijadhadh.2021.102947
19. Singh N., Rana A., Badhotiya G.K. Raw Material Particle Terminologies for Development of Engineered Wood. Materials Today: Proceedings, 2021, vol. 46, part 10,pp. 11243–11246. https://doi.org/10.1016/j.matpr.2021.02.616
20. Skurydin Yu.G., Skuridina E.M. Physical and Mechanical Characteristics of the Thermal-Wood Composition from Hydrolyzed Birch Wood. IOP Conference Series: Earth and Environmental Science, 2019, vol. 316, art. 012066. https://doi.org/10.1088/1755-1315/316/1/012066
21. Skurydin Yu.G., Skurydina E.M. Digital Differential Spectrometry in the Assessment of the Structural Characteristics of Wood and Wooden Composite Materials. IOP Conference Series: Earth and Environmental Science, 2021, vol. 806, art. 012030. https://doi.org/10.1088/1755-1315/806/1/012030
22. Startsev O.V., Salin B.N., Skuridin Y.G., Utemesov R.M., Nasonov A.D. Physical Properties and Molecular Mobility of the New Wood Composite Plastic “Thermobalite”. Wood Science and Technology, 1999, vol. 33, iss. 1, pp. 73–83. https://doi.org/10.1007/s002260050100
23. Uemura Silva V., Nascimento M.F., Resende Oliveira P., Panzera T.H., Rezende M.O., Silva D.A.L., Borges de Moura Aquino V., Rocco Lahr F.A., Christoforo A.L. Circular vs. Linear Economy of Building Materials: A Case Study for Particleboards Made of Recycled Wood and Biopolymer vs. Conventional Particleboards. Construction and Building Materials, 2021, vol. 285, art. 122906. https://doi.org/10.1016/j.conbuildmat.2021.122906