Address: 17 Naberezhnaya Severnoy Dviny, Arkhangelsk 163002 Russian Federation. Northern (Arctic) Federal University named after M.V.Lomonosov. Office 1425

Phone / Fax: (818-2) 21-61-18
E-mail: forest@narfu.ru
http://lesnoizhurnal.ru/en/

RussianEnglish



Archive

Measurement of Bending Stiffness of Corrugated Board

Версия для печати
Creative Commons License
These works are licensed under a Creative Commons Attribution 4.0 International License.

E.Yu. Larina, Ya.V. Kazakov

Complete text of the article:

Download article (pdf, 0.8MB )

UDС

676.274

DOI:

DOI: 10.17238/issn0536-1036.2016.1.155

Abstract

The corrugated boxes are a very common type of packaging. The standard and additional features of corrugated board, primarily the bending stiffness are used in order to predict their behavior under operating conditions. The 4-point method is more valid of all the methods of measuring the bending stiffness of corrugated board. The information on the use of it is cur-rently insufficient. The paper presents a method of measuring the stiffness of corrugated board with the 4-point bending mode on the device “L&W 4-point Bending Stiffness Tester SE 108”. The analysis of the factors affecting on the test results is carried out on the samples of C-flute single-wall corrugated board of different brands of T22 to T25. The influence of the sample length within the range from 100...200 mm and a loaded weight in the range from 70...220 grams is studied. The advantage of acceptance as a result of the geometric mean of bending stiffness, measured in the machine (MD) and cross machine (CD) direc-tions is shown. It is established experimentally that the increasing the length of the sample and the applied load decreased bending stiffness of corrugated board. The greatest impact of the sample length affects at the low values of the applied load and the effect of the applied load – at a small length of the sample. It is found that the anisotropy of bending stiffness of corrugated board of the low grade T22 (2.7...3.1) was higher than that of the high grade T25 (2.5...2.7). The anisotropy of bending stiffness decreases with the increasing of the sample length. For the accurate and reliable measurement the length of the test sample of corrugated board should be at least 200 mm, as in this case the influence of other factors almost has no effect. The magnitude of the applied load depends on the brand of corrugated board and should be within the range from 120...220 grams. The results can improve the accuracy of the assessment of corrugated board quality and provide a more reliable prediction of the properties of the corrugated boxes.

Authors

E.Yu. Larina, Candidate of Engineering Ya.V. Kazakov, Candidate of Engineering

Affiliation

Northern (Arctic) Federal University named after M.V. Lomonosov, Naberezhnaya Severnoy Dviny, 17, Arkhangelsk, 163002, Russian Federation; е-mail: ketrin@bk.ru, j.kazakov@narfu.ru

Keywords

corrugated board, bending, bending resistance, bending stiffness.

References

1. GOST 7376–89. Karton gofrirovannyy. Obshchie tekhnicheskie usloviya [State Standard 7376-89. Corrugated Board. General Specifications]. Moscow, 1991.
2. Kazakov Ya.V., Gur'ev A.V., Komarov V.I., Kryzhanovskiy A.O. Zhuravleva A.N. Zhestkost' pri izgibe gofrokartona [Bending Stiffness of Corrugated Board]. Tsellyulo-za. Bumaga. Karton [Pulp. Paper. Board], 2006, no. 6, pp. 50–52.
3. Komarov V.I. Deformativnost' tsellyulozno-bumazhnykh materialov pri izgibe [Strain Capacity of Pulp and Paper Materials under Bending]. Lesnoy zhurnal, 1994, no. 1, pp. 96–103.
4. Komarov V.I. Zhestkost' pri izgibe tsellyulozno-bumazhnykh materialov. Analiz metodov izmereniya i vliyaniya tekhnologicheskikh faktorov [Bending Stiffness of Pulp and Paper Materials. Analysis of the Measuring Methods and the Impact of Technological Fac-tors]. Lesnoy zhurnal, 1994, no. 3, pp. 133–142.
5. Komarov V.I., Gur'ev A.V., El'kin V.P. Mekhanika deformirovaniya tsellyuloz-nykh taroupakovochnykh materialov [Mechanics of Deformation of Cellulose Packaging Materials]. Arkhangelsk, 2002. 175 p.
6. Komarov V.I., Larina E.Yu. Raschet zhestkosti pri izgibe voloknistykh tsellyuloz-no-bumazhnykh materialov s uchetom plasticheskoy deformatsii v szhatoy zone v ploskosti lista [Calculation of the Bending Stiffness of Fibrous Pulp and Paper Materials with Regard to Plastic Deformation in the Compression Region in the Sheet Plane]. Lesnoy zhurnal, 2009, no. 4, pp. 106–110.
7. Larina E.Yu., Komarov V.I. Vliyanie plasticheskikh deformatsiy po tolshchine i v ploskosti lista, voznikayushchikh pri ispytanii na izgib, na velichinu izmeryaemoy kharak-teristiki [Effect of Plastic Deformation in Thickness and Paper Sheet Plane Occurring in Bending on Measured Parameter Value]. Lesnoy zhurnal, 2010, no. 4, pp. 89–95.
8. L&W 4-Point Bending Stiffness Tester. Manual. Available at: http:// l-w.com/produkt/lw-4-point-bending-stiffness-tester.
9. Smolin A.S., Komarov V.I., Dubovyy V.K., Beloglazov V.I. Tekhnologiya go-frokartona. Chast' 1 [Technology of Corrugated Board. Part I]. Saint Petersburg, 2014. 146 p.
10. Blechschmidt J. Papierverarbeitungstechnik. Dresden, 2012. 576 p.
11. Markstrom H. Testing Methods and Instruments for Corrugated Board. Elanders Tofters AB, 1999. 103 p.
Received on May 13, 2015

Measurement of Bending Stiffness of Corrugated Board

 

Make a Submission


ADP_cert_2024.png

Lesnoy Zhurnal (Russian Forestry Journal) was awarded the "Seal of Recognition for Active Data Provider of the Year 2024"

INDEXED IN: 

scopus.jpg

DOAJ_logo-colour.png

logotype.png

Логотип.png