Address: 17 Naberezhnaya Severnoy Dviny, Arkhangelsk 163002 Russian Federation. Northern (Arctic) Federal University named after M.V.Lomonosov. Office 1425

Phone / Fax: (818-2) 21-61-18
E-mail: forest@narfu.ru
http://lesnoizhurnal.ru/en/

RussianEnglish



Archive

Determination of the Initial Stiffness of Unstretched Rolled Strip Saws

Версия для печати
Creative Commons License
These works are licensed under a Creative Commons Attribution 4.0 International License.

G.F. Prokofiev, A.M. Tyurin, M.Yu. Kabakova, O.L. Kovalenko

Complete text of the article:

Download article (pdf, 0.7MB )

UDС

621.933.3

DOI:

10.37482/0536-1036-2020-3-143-150

Abstract

The paper presents the results of studies of the initial stiffness of rolled strip unstretched saws; theoretically obtained and experimentally confirmed. A mathematical model, that allows calculating the initial stiffness of unstretched strip saws, has been developed in order to justify the distance between the guides and the saw parameters for precise sawing. Experiments were performed for verifying the validity of the assumptions made in carrying out the theoretical research. The analysis of the research results and the following conclusions are made: theoretical and experimental values of the initial stiffness of rolled strip saws practically coincide (the difference does not exceed 2 %); the stiffness of the rolled saw according to the theoretical data exceeds the stiffness of the non-rolled saw by more than 80 %. According to the technological modes of RPI 6.1-00 “Preparation of Frame Saws” to ensure the required accuracy of wood sawing, the initial stiffness of the strip saw should be at least 60–70 N/mm. The obtained results allow us to determine the main parameters of unstretched strip saws providing this condition.

Authors

G.F. Prokofiev1, Doctor of Engineering, Prof.; ResearcherID: G-9482-2019,
ORCID: https://orcid.org/0000-0003-4494-4989
A.M. Tyurin2, Candidate of Engineering, Leading Engineer; ResearcherID: G-9823-2019,
ORCID: https://orcid.org/0000-0003-1250-2238
M.Yu. Kabakova1, Candidate of Engineering, Assoc. Prof.; ResearcherID: F-6036-2019,
ORCID: https://orcid.org/0000-0002-4158-9224
O.L. Kovalenko1, Postgraduate Student; ResearcherID: H-1812-2019,
ORCID: https://orcid.org/0000-0003-1817-3949

Affiliation

1Northern (Arctic) Federal University named after M.V. Lomonosov, Naberezhnaya Severnoy Dviny, 17, Arkhangelsk, 163002, Russian Federation; e-mail: g.prokofjev@narfu.rum.kabakova@narfu.ru, o.kovalenko@narfu.ru
2PJSC Severalmaz, ul. Karla Marksa, 15, Arkhangelsk, 163000, Russian Federation; e-mail: alexejtyrin@rambler.ru

Keywords

accuracy of wood sawing, initial stiffness of strip saws, conditions for precise sawing, guides for saws, stress condition when rolling

For citation

Prokofiev G.F., Tyurin A.M., Kabakova M.Yu., Kovalenko O.L. Determination of the Initial Stiffness of Unstretched Rolled Strip Saws. Lesnoy Zhurnal [Russian Forestry Journal], 2020, no. 3, pp. 143–150. DOI: 10.37482/0536-1036-2020-3-143-150

References

1. Blokhin M.A. Research, Development and Creation of Sawmill Equipment with Circular and Translational Movement of Saw Blades: Dr. Sci. Diss. Arkhangelsk, 2015. 284 p.
2. Grube A.E. Wood Cutting Tools. Moscow, Goslesbumizdat Publ., 1958. 472 p.
3. Ivankin I.I. Theoretical Studies of the Initial Stiffness of Band Saws. Lesnoy Zhurnal [Russian Forestry Journal], 2000, no. 3, pp. 112–119.
4. Prokofiev G.F., Tyurin A.M. Sawmill Cutting Unit. Patent RF no. RU 117847 U1, 2012.
5. Prokof’ev G.F., Miklovtsik N.J., Tjurin A.M. Saw Mill Cutting Assembly. Patent RF no. RU 2452615 C1, 2012.
6. Prokof’ev G.F., Miklovtsik N.J., Tjurin A.M. Method of Mounting Guides for Floating Non-Stretched Sawmill Bands. Patent RF no. RU 2480324 C1, 2013.
7. Prokofiev G.F. Technological Modes of RPI 6.1-00 “Preparation of Frame Saws”. Arkhangelsk, TsNIIMOD Publ., 1986. 44 p.
8. Prokofiev G.F. Intensification of Sawing Wood by Frame and Band Saws. Moscow, Lesnaya promyshlennost’ Publ., 1990. 240 p.
9. Prokofiev G.F., Ivankin I.I. Improving the Efficiency of Sawing Wood on Saw Frames and Band Saws. Arkhangelsk, ASTU Publ., 2009. 380 p.
10. Prokofiev G.F., Ivankin I.I., Dundin N.I. Investigation of Initial Hardness of Strip Saws. Lesnoy Zhurnal [Russian Forestry Journal], 2001, no. 3, pp. 88–95. URL: http://lesnoizhurnal.ru/upload/iblock/432/4326ee98c21689129b0fa784fd7c48f7.pdf
11. Prokofiev G.F., Ivankin I.I., Kazantsev V.A. Improving the Quality of Sawing Wood at Sawmills. Arkhangelsk, ASTU Publ., 2007. 192 p.
12. Timoshenko S.P. Stability of Elastic Systems. Moscow, Gostekhizdat Publ., 1955, vol. 2. 567 p.
13. Тимошенко С.П. Сопротивление материалов. 3-е изд. М.: Наука, 1965. Т. 2. 480 с. [Timoshenko S.P. Strength of Materials. Moscow, Nauka Publ., 1965, vol. 2. 480 p.].
14. Bathe K.J. Finite Element Procedures in Engineering Analysis. New Jersey, Prentice Hall, 1982. 735 p.
15. Calladine C.R. Theory of Shell Structures. Cambridge, Cambridge University Press, 1983. 763 p. DOI: 10.1017/CBO9780511624278
16. Hughes T.J.R., Hinton E. Finite Element Methods for Plates and Shells: Elements Technology. Swansea, Pineridge Press, 1986, vol. 1. 315 p.
17. Hughes T.J.R., Hinton E. Finite Element Methods for Plates and Shells: Formulations and Algorithms. Swansea, Pineridge Press, 1986, vol. 2. 320 p.
18. Irons B., Ahmad S. Techniques of Finite Elements. New York, E. Horwood, 1980. 529 p.
19. Kivimaa E. Cutting Force in Frame Sawing. Paperiia puu, 1959, vol. 41, no. 1, pp. 13–16.
20. Porter A. Some Engineering Consideration of High-Strain. Forest Products Journal, 1977, vol. 21, no. 4, pp. 24–32.
21. Thunell B. The Stability of the Band Saw Blade. Holz als Roh- und Werkstoff, 1970, vol. 28, iss. 9, pp. 343–348.

Determination of the Initial Stiffness of Unstretched Rolled Strip Saws

 

Make a Submission


ADP_cert_2024.png

Lesnoy Zhurnal (Russian Forestry Journal) was awarded the "Seal of Recognition for Active Data Provider of the Year 2024"

INDEXED IN: 

scopus.jpg

DOAJ_logo-colour.png

logotype.png

Логотип.png