Address: 17 Naberezhnaya Severnoy Dviny, Arkhangelsk 163002 Russian Federation. Northern (Arctic) Federal University named after M.V.Lomonosov. Office 1425

Phone / Fax: (818-2) 21-61-18
E-mail: forest@narfu.ru
http://lesnoizhurnal.ru/en/

RussianEnglish



Archive

The Modes of Laser Hardening of Alloyed Steel Wood-Cutting Tools

Версия для печати
Creative Commons License
These works are licensed under a Creative Commons Attribution 4.0 International License.

L.V. Kremleva, V.I. Malygin, K.K. Snegireva

Complete text of the article:

Download article (pdf, 0.4MB )

UDС

621.983.32:621.78-977

DOI:

10.17238/issn0536-1036.2016.5.157

Abstract

One of the most promising directions of increasing the wear resistance and durability of wood-cutting tools is a hardening of working surfaces by a laser beam. The article presents the results of experimental studies of the process of laser hardening of alloyed tool steels, widely used for the manufacture of milling wood-cutting tools. The preliminary volume heat treatment of tool steel samples has a significant influence on the quality parameters of the surface layer (residual stresses, hardening depth, surface micro-hardness) in the subsequent laser hardening. The experiments are carried out at the pulsed laser strengthening installa-tion «Kvant-18» with a pulse length of 8 ms on the samples of 9XS and CWM steels. Re-sidual stresses of the hardened zone and residual austenite are determined by Rigaku FSM-2M, the microhardness is measured on the micro-sections by a hardness tester PMT-3. The first series of experiments in laser hardening are carried out on unquenched samples. The laser effect on the structurally nonhomogeneous sample leads to adverse tensile surface stresses, microhardness changes slightly. In the second series of experiments the samples are subjected to volume heat treatment. For the quality of laser hardening after a volume heat treatment it is necessary to carry out low tempering. With increasing the tempering tempera-ture the residual austenite decreases in the surface layer of a hardenable part, which reduces the size of the hardened layer and the microhardness of the surface. The pre-quenching tem-perature rise has a positive effect on the quality parameters of the hardenable layer, but ma-chinability of tool steels significantly decreases that can adversely affect the machining op-erations of working and basing tools faces (including grinding) prior to the operation of la-ser hardening.

Authors

L.V. Kremleva, Doctor of Engineering Sciences, Associate Professor V.I. Malygin, Doctor of Engineering Sciences, Professor K.K. Snegireva, Postgraduate Student

Affiliation

Northern (Arctic) Federal University named after M.V. Lomonosov, Captain Voronin str., 6, Severodvinsk, Arkhangelsk region, 164500, Russian Federation;
e-mail: kremleva67@mail.ru

Keywords

wood-cutting tool, laser hardening, hardening, tempering, retained austenite, hardened layer depth, micro-hardness.

References


1. Zotov G.A, Pamfilov E.A. Povyshenie stoykosti derevorezhushchego instrumenta [Increasing of Wood-Cutting Tools Resistance]. Moscow, 1991. 295 p.
2. Biryukov V. Izmenenie struktury i svoystv staley pri lazernom uprochenii [Chang-es in the Structure and Properties of Steels at Laser Consolidation]. Fotonika [Photonics], 2012, no. 3, pp. 22–27.
3. Brover A.V., Brover G.I., D'yachenko L.D. Nekotorye osobennosti strukturnogo sostoyaniya staley v zonakh lazernoy obrabotki [Some Features of the Structural State of Steels in the Areas of Laser Processing]. Chernaya metallurgiya [Ferrous Metallurgy], 2007, no. 6, pp. 36–45.
4. Grigor'yants A.G., Shchiganov I.N., Misyurov A.I. Tekhnicheskie protsessy laz-ernoy obrabotki [The Technological Processes of Laser Processing]. Moscow, 2006. 664 p.
5. Gureev D.M., Kamashev A.V., Yamshchikov S.V. Mekhanizmy fazovykh prev-rashcheniy v zheleze i stalyakh pri lazernom nagreve [The Mechanisms of Phase Transfor-mations in Iron and Steel by Laser Heating]. Samara, 1999. 164 p.
6. Moiseev A.V. Iznosostoykost' derevorezhushchego instrumenta [Wear Resistance of Wood-Cutting Tools]. Moscow, 1981. 111 p.
7. Popov V.S. Lazernoe uprochnenie staley: sravnenie volokonnykh i СO2-lazerov [Steels Laser Hardening: a Comparison of Fiber and CO2 Lasers]. Fotonika [Photonics], 2009, no. 4, pp. 18–21.
8. Pronin M.M., Startsev V.N., Popov V.O., Vaynerman A.E., Kalganov B.D. Laz-ernaya obrabotka materialov. Perspektivnye tekhnologii i oborudovanie [Laser Materials Processing. Advanced Technologies and Equipment]. Voprosy materialovedeniya, 1999, no. 3, pp. 375–393.
9. Sinyakov K.A. Vliyanie skorosti nagreva na strukturu i svoystva instrumental'nykh staley [Effect of Heating Rate on the Structure and Properties of Tool Steels]. Instrument i tekhnologii, 2008, no. 5, pp. 151–158.
10. Sitkina L.P., Yares'ko S.I. Effektivnost' tekhnologii lazernoy uprochnyayushchey obrabotki v instrumental'nom proizvodstve [The Effectiveness of Laser Hardening Treat-ment Technology in Tool Production]. Izvestia VSTU, 2013, vol. 9, no. 7, pp. 40–43.
11. Somonov V.V., Tsibul'skiy I.A. Effektivnost' ispol'zovaniya volokonnykh lazerov dlya lazernoy zakalki izdeliy v promyshlennosti [The Effectiveness of the Use of Fiber Lasers for Laser Hardening of Products in the Industry]. Metalloobrabotka, 2014, no. 1, pp. 9–12.
12. Yares'ko S.I., Goryainov D.S. Modelirovanie protsessa lazernogo uprochneniya rezhushchego instrumenta [The Simulation of Laser Hardening of Cutting Tools]. Izvestiya Samarskogo nauchnogo tsentra RAN [Proceedings of the Samara Scientific Center of the Russian Academy of Sciences], 2011, vol. 13, no. 4–3, pp. 921–926.
13. Adel K.M., Dhia A.S., Ghazali M.J. The Effect of Laser Surface Hardening on the Wear and Friction Characteristics of Acicular Bainitic Ductile Iron. International Journal of Mechanical and Materials Engineering, 2009, vol. 4, no. 2, pp. 167–171.
14. El-Batahgy A.M., Ramadan R.A., Moussa A.R. Laser Surface Hardening of Tool Steels – Experimental and Numerical Analysis. Journal of Surface Engineered Materials and Advanced Technology, 2013, no. 3, pp. 146–153.
15. Lee J.H., Jang J.H., Joo B.D., Son Y.M., Moon Y.H. Laser Surface Hardening of AISI H13 Tool Steel. Transactions of Nonferrous Metals Society of China, 2009, vol. 19, no. 4, pp. 917–920.
Received on May 20, 2015

The Modes of Laser Hardening of Alloyed Steel Wood-Cutting Tools

 

Make a Submission


ADP_cert_2024.png

Lesnoy Zhurnal (Russian Forestry Journal) was awarded the "Seal of Recognition for Active Data Provider of the Year 2024"

INDEXED IN: 

scopus.jpg

DOAJ_logo-colour.png

logotype.png

Логотип.png