Почтовый адрес: САФУ, Редакция «Лесной журнал», наб. Северной Двины, 17, г. Архангельск, Россия, 163002, ауд. 1425

Тел.: 8(8182) 21-61-18
Сайт: http://lesnoizhurnal.ru/ 
e-mail: forest@narfu.ru

RussianEnglish



архив

Исходные технологические требования системы позиционирования суппорта обрезного станка от линейного асинхронного двигателя

Версия для печати

А.Е. Алексеев, М.В. Кришьянис

Рубрика: Механическая обработка древесины

Скачать статью (pdf, 0.5MB )

УДК

674.053:621.934/.936

DOI:

10.17238/issn0536-1036.2018.6.149

Аннотация

В работе дана характеристика операции формирования ширины обрезных пиломатериалов на базе станка Ц2Д-5А; изучен механизм управления подвижной пилой посредством ручной установки гидропозиционера на размер обрезаемой доски по ширине. Сформулированы общие методические положения по формированию сечений пиломатериалов; выполнен анализ результатов формообразования размеров обрезных пиломатериалов. Представлена классификация систем управления деревообрабатывающими станками. Разработаны исходные технологические требования для системы позиционирования суппорта обрезного станка от линейного асинхронного двигателя, учтены изменения характеристик выхода пиломатериалов в зависимости от сочетаний толщин тонких и толстых досок. Установлено, что выставка штока (вторичного элемента) линейного асинхронного двигателя на максимальную длину соответствует наименьшей ширине обрезной доски с учетом припуска на ее усушку по номинальной ширине. При этом базовой поверхностью служит воображаемая плоскость, параллельная плоскости неподвижной круглой пилы двухпильного станка и касательная в точках, определяемых положениями ее зубьев с регламентируемым уширением на сторону. Началом отсчета номинальной ширины обрезной доски является плоскость, располагающаяся параллельно базовой и отстоящая от нее на величину, равную номинальной ширине доски с припуском на усушку.

Сведения об авторах

А.Е. Алексеев, д-р техн. наук, проф.
М.В. Кришьянис, ст. преподаватель
Северный (Арктический) федеральный университет им. М.В. Ломоносова, наб. Северной Двины, д. 17, г. Архангельск, Россия, 163002; е-mail: a.alekseev@narfu.ru, m.krishjyanis@narfu.ru

Ключевые слова

система позиционирования, линейный асинхронный двигатель, исходные технологические требования, обрезка пиломатериалов

Для цитирования

Алексеев А.Е., Кришьянис М.В. Исходные технологические требования системы позиционирования суппорта обрезного станка от линейного асинхронного двигателя // Лесн. журн. 2018. № 6. С. 149–159. (Изв. высш. учеб. заведений). DOI: 10.17238/issn0536-1036.2018.6.149

Литература

1. Алексеев А.Е., Алексеева Л.В. Организация малых лесопильных предприятий. Архангельск: АГТУ, 2007. 731 с.
2. Варфоломеев Ю.А., Дружин И.С., Дьячков Ю.А. Справочник по лесопилению / под ред. А.М. Копейкина. Изд. 2-е, перераб. и доп. М.: Экология, 1991. 495 с.
3. Клюев В.А. Распределение бревен по диаметру и сбегу // Науч. тр. ЦНИИМОД. Архангельск: ЦНИИМОД, 1973. Вып. 28. С. 77–80.
4. Кулиш В.Г., Коротов С.С. Распределение пиловочника бревен по диаметрам // Совершенствование технологии и оборудования лесопильного производства: науч. тр. ЦНИИМОД. Архангельск: ЦНИИМОД, 1981. С. 10–14.
5. Покотило В.П. Специализация лесопильных предприятий. М.: Лесн. пром-сть, 1977. 97 с.
6. Покотило В.П. Специализация лесоэкспортных предприятий производственного объединения «Северолесоэкспорт» / Всесоюз. науч.-исслед. и проект. ин-т экономики, организации управления пр-вом и информ. по лес., целлюлоз.-бумаж. и деревообраб. пром-сти. М.: ВНИПИЭИлеспром, 1977. 54 с.
7. Шимкевич Ю.Б. Справочник по лесопилению. СПб.: ПРОФИ-ИНФОРМ, 2005. 200 с.
8. Ясинский В.С., Кучин А.В. О законе распределения пиловочного сырья по длинам // Технология и оборудование деревообрабатывающих производств. Процессы механической обработки, склеивания и отделки древесины. Л.: ЛТА, 1983. С. 8–10.
9. Alekseev A.E., Krisjanis M.V. Evaluation of the Thermal State of a Linear Induction Motor Operating as a Positioner in the Edging Machine // International Conference on Advanced Research in Business, Economics, Law and Social Sciences. Section 2. Electrical Engineering, Madrid, November 15, 2017. Madrid, 2017. Pp. 17–25.
10. Birkeland R., Timland H. Practical Experience with a Fully Automated Line Camera Scanning System in a Window Manufacturing Company // Proceedings of the 3rd International Conference on Scanning Technology in Sawmilling, San Francisco, 1989. San Francisco, 1989. Pp. xx-1–9.
11. Chang S.J. External and Internal Defect Detection to Optimize Cutting of Hardwood Logs and Lumber // Transferring Technologies to the Hardwood Industry: Handbook No. 3. / U.S. Department of Commerce. Beltsville, MD, 1992. 24 p.
12. Niskanen M., Silvén O., Kauppinen H. Experiments with SOM Based Inspection of Wood // International Conference on Quality Control by Artificial Vision (QCAV2001), Le Creusot, 2001. Le Creusot, France, 2001. No. 2. Pp. 311–316.
13. Rieth P.A., Good D. Scanning for Lumber Defects and Ripsaw Optimization: A Case Study // Proceedings of the 3rd International Conference on Scanning Technology in Sawmilling, San Francisco, October 5–6, 1989. San Francisco. 1989. Pp. XV-1–28.

Поступила 13.04.18


UDC 674.053:621.934/.936
DOI: 10.17238/issn0536-1036.2018.6.149

Initial Technological Requirements for Position Control System of Edging Machine
Support from Linear Induction Motor

A.E. Alekseev, Doctor of Engineering Sciences, Professor
M.V. Krisjanis, Senior Lecturer
Northern (Arctic) Federal University named after M.V. Lomonosov, Naberezhnaya
Severnoy Dviny, 17, Arkhangelsk, 163002, Russian Federation; е-mail: a.alekseev@narfu.ru, m.krishjyanis@narfu.ru

The paper gives characteristic to the operation of width formation of edging sawn timber on the basis of the Ts2D-5A machine. The mechanism of control a mobile saw by the means of manual installation of a hydropositioner on the size of a cutting board across the width is studied. The general methodological regulations on formation of sawn timber sections are formulated; the results analysis of geometry forming of edged sawn timber is done. The article presents a classification of control systems of woodworking machines. The initial technological requirements of position control system for edging machine support from the linear induction motor are developed; changes in the output characteristics of sawn timber depending on the combination of thin and thick board thicknesses are taken into account. It is established that adjustment of stock (secondary element) of the linear induction motor for maximum length corresponds to the smallest width of edging board with allowance for its shrinkage across the nominal width. In this case, imaginary plane parallel to plane of a fixed circular saw of double saw machine and tangent at the points determined by the positions of saw teeth with the controlled broadening on the side is a base surface. Reference position of the nominal width of edged board is a plane parallel to the base surface and spaced away from it by the nominal width of the board with allowance for shrinkage.

Keywords: position control system, linear induction motor, initial technological requirements, sawn timber edging.

REFERENCES

1. Alekseeev A.E., Alekseeeva L.V. Organizatsiya malykh lesopil’nykh predpriyatiy [Organization of Small Sawmills]. Arkhangelsk, ASTU Publ., 2007. 731 p. (In Russ.)
2. Varfolomeyev Yu.A., Druzhin I.S., D’yachkov Yu.A. Spravochnik po lesopileniyu [Handbook of Sawmilling]. Ed. by A.M. Kopeikin. Moscow, Ekologiya Publ., 1991. 495 p. (In Russ.)
3. Klyuyev V.A. Raspredeleniye breven po diametru i sbegu [Distribution of Logs by Diameter and Taper]. Nauch. tr. TSNIIMOD [Academic Papers of the Central Research Institute of Mechanical Wood Processing]. Arkhangelsk, TSNIIMOD Publ., 1973, iss. 28, pp. 77–80.
4. Kulish V.G., Korotov S.S. Raspredeleniye pilovochnika breven po diametram [Distribution of Lumber Logs by Diameter]. Sovershenstvovaniye tekhnologii i oborudovaniya lesopil’nogo proizvodstva: nauch. tr. TSNIIMOD [Improvement of Technology and Equipment for Sawmill Production: Academic Papers of the Central Research Institute of Mechanical Wood Processing]. Arkhangelsk, TSNIIMOD Publ., 1981, pp. 10–14.
5. Pokotilo V.P. Spetsializatsiya lesopil’nykh predpriyatiy [Differentiation of Sawmills]. Moscow, Lesnaya promyshlennost’ Publ., 1977. 97 p. (In Russ.)
6. Pokotilo V.P. Spetsializatsiya lesoeksportnykh predpriyatiy proizvodstvennogo ob”yedineniya «Severolesoeksport» [Differentiation of Timber Export Enterprises of the Industrial Association “Severolesoeksport”]. Vsesoyuz. nauch.-issled. i proyektnyy in-t ekonomiki, organizatsii upravleniya pr-vom i inform. po les., tsellyuloz.-bumazhn. i derevoobrab. prom-sti [All-Union Sci.-Res. and Project Institute of Economics, Organization of Production Management and Information on Forest, Pulp and Paper and Woodworking Industry]. Moscow, VNIPIEIlesprom Publ., 1977. 54 p. (In Russ.)
7. Shimkevich Yu.B. Spravochnik po lesopileniyu [Handbook of Sawmilling]. Saint Petersburg, PROFI-INFORM Publ., 2005. 200 p. (In Russ.)
8. Yasinskiy V.S., Kuchin A.V. O zakone raspredeleniya pilovochnogo syr’ya po dlinam [On the Law of Distribution of Sawing Raw Material by Lengths]. Tekhnologiya i oborudovaniye derevoobrabatyvayushchikh proizvodstv. Protsessy mekhanicheskoy obrabotki, skleivaniya i otdelki drevesiny [Technology and Equipment for Woodworking Industries. Mechanical Processing, Gluing and Fashioning of Wood]. Leningrad, LTA Publ., 1983, pp. 8–10.
9. Alekseev A.E., Krisjanis M.V. Evaluation of the Thermal State of a Linear Induction Motor Operating as a Positioner in the Edging Machine. International Conference on Advanced Research in Business, Economics, Law and Social Sciences. Section 2. Electrical Engineering, Madrid, November 15, 2017. Madrid, 2017, pp. 17–25.
10. Birkeland R., Timland H. Practical Experience with a Fully Automated Line Camera Scanning System in a Window Manufacturing Company. Proceedings of the 3rd International Conference on Scanning Technology in Sawmilling, San Francisco, 1989. San Francisco, 1989, pp. xx-1–9.
11. Chang S.J. External and Internal Defect Detection to Optimize Cutting of Hardwood Logs and Lumber. Transferring Technologies to the Hardwood Industry: Handbook No. 3. U.S. Department of Commerce, Beltsville, MD, 1992. 24 p.
12. Niskanen M., Silvén O., Kauppinen H. Experiments with SOM Based Inspection of Wood. International Conference on Quality Control by Artificial Vision (QCAV2001), Le Creusot, 2001. Le Creusot, France, 2001, no. 2, pp. 311–316.
13. Rieth P.A., Good D. Scanning for Lumber Defects and Ripsaw Optimization: A Case Study. Proceedings of the 3rd International Conference on Scanning Technology in Sawmilling, San Francisco, October 5–6, 1989. San Francisco. 1989, pp. XV-1–28.

Received on April 13, 2018


For citation: Alekseev A.E., Krisjanis M.V. Initial Technological Requirements for Position Control System of Edging Machine Support from Linear Induction Motor. Lesnoy Zhurnal [Forestry Journal], 2018, no. 6, pp. 149–159. DOI: 10.17238/issn0536-1036.2018.6.149