Address: 17 Naberezhnaya Severnoy Dviny, Arkhangelsk 163002 Russian Federation. Northern (Arctic) Federal University named after M.V.Lomonosov. Office 1425

Phone / Fax: (818-2) 21-61-18
E-mail: forest@narfu.ru
http://lesnoizhurnal.ru/en/

RussianEnglish



Archive

Finding the Equilibrium Conditions of the Processing Object in the Machine-Tool-Wood System of Sawmill Unit

Версия для печати
Creative Commons License
These works are licensed under a Creative Commons Attribution 4.0 International License.

V.V. Taratin

Complete text of the article:

Download article (pdf, 0.6MB )

UDС

674.093: 621.914.1

DOI:

10.17238/issn0536-1036.2015.1.117

Abstract

The equilibrium conditions of the processing object in the machine-tool-wood system of the sawmill unit were considered for one of its possible variations, for the cross-cutting unit. Its use is a rational way to increase the yield and quality of pulpchips, especially under buck of short sections of boards, processing of which is inefficient on traditional equipment - chippers. Machine-tool-wood system of sawmill unit c conditionally have been viewed as a rod system with two degrees of static indeterminacy, subordinated to the main position of the elasticity theory. The method of the structural mechanics forces was applied for the disclosure of static indeterminacy of the system. Unknowns of the system under construction the equations of deformation were applied force system parameters corresponding to the amount of redundant connections according to this method. Dependences were obtained to determine the minimum die hold-down pressure of board under milling, deformation parameters in the machine-tool-wood system of cross-cutting unit, and distribution diagrams of bending moments and longitudinal forces in this system were built. Analysis of distribution diagrams and obtained dependences showed the following. Counter cross-milling with top location of board is the most rational to ensure equilibrium conditions. It is essential to use a compulsory hold-down of board. This is a prerequisite process of cross-cutting by milling with the required indexes of quality products. Based on these results the rational design and technological parameters of the milling process, when is cross-cutting of boards, is necessary to determine. These parameters at best (optimal) should ensure minimization of raw material and energy costs in the development of saw-timber and pulpchips according to the requirements of resource saving. This is true not only for cross-milling by stepped circular cutter, but also for longitudinal milling by face-conical (conical) and circular cutter, which are used in a varieties of milling equipment besides considering cross-cutting unit.

Authors

V.V. Taratin, Candidate of Engineеring, Associate Professor

Affiliation

Northern (Arctic) Federal University named after M.V. Lomonosov, Naberezhnaya Severnoy Dviny, 17, 163002 Arkhangelsk, Russia; е-mail: taratinvjacheslav@rambler.ru

Keywords

equilibrium, processing object, system MTW (machine-tool-wood), sawmill unit, resource saving requirements.

References

1. Borovikov E.M., Fefilov L.A., Shestakov V.V. Lesopilenie na agregatnom oborudovanii [Sawmilling on the Unit-Type Equipment]. Moscow, 1985. 216 p. 2. Snitko N.K. Stroitel'naya mekhanika [Structural Mechanics]. Moscow, 1972, 488 p. 3. Taratin V.V. Agregatnyy metod obrabotki dosok po dline i puti ego realizatsii [Unit-Type Method of Boards Processing on Length and a Way of Its Realization]. Novye tekhnologicheskie protsessy v lesopilenii: nauch. tr. [New Technological Processes in Sawmilling: Proceedings]. 1986, pp. 93–100. 4. Taratin V.V. Primenenie frezernogo modulya dlya polucheniya tekhnologicheskoy shchepy pri tortsovke pilomaterialov [Use of the Milling Module for Receiving Pulpchips at Cross-Cutting of Sawn-Timber]. Protsessy rezaniya, oborudovanie i avtomatizatsiya v derevoobrabotke: nauch. tr. [Cutting Processes, the Equipment and Automation in a Woodworking: Proceedings]. 1991, no. 236, pp. 35–42.

Finding the Equilibrium Conditions of the Processing Object in the Machine-Tool-Wood System of Sawmill Unit

 

Make a Submission


ADP_cert_2024.png

Lesnoy Zhurnal (Russian Forestry Journal) was awarded the "Seal of Recognition for Active Data Provider of the Year 2024"

INDEXED IN: 


DOAJ_logo-colour.png

logotype.png

Логотип.png